[arch-general] talkingarch problems formatting partitions
Don Raikes
DON.RAIKES at ORACLE.COM
Thu Mar 13 00:58:10 EDT 2014
Hi Simon,
I ran# smartctl -x /dev/sda
Results:
smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.6.6-1-ARCH] (local build)
Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K1000.C
Device Model: Hitachi HDS721010CLA332
Serial Number: JP9921HD2SB0VH
LU WWN Device Id: 5 000cca 373e6ccf0
Firmware Version: JP4OA3MA
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Mar 13 04:47:08 2014 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (10282) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 171) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0
2 Throughput_Performance P-S--- 135 135 054 - 98
3 Spin_Up_Time POS--- 173 173 024 - 230 (Average 207)
4 Start_Stop_Count -O--C- 100 100 000 - 438
5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
7 Seek_Error_Rate PO-R-- 100 100 067 - 0
8 Seek_Time_Performance P-S--- 140 140 020 - 30
9 Power_On_Hours -O--C- 099 099 000 - 11134
10 Spin_Retry_Count PO--C- 100 100 060 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 438
192 Power-Off_Retract_Count -O--CK 100 100 000 - 554
193 Load_Cycle_Count -O--C- 100 100 000 - 554
194 Temperature_Celsius -O---- 193 193 000 - 31 (Min/Max 19/51)
196 Reallocated_Event_Count -O--CK 100 100 000 - 0
197 Current_Pending_Sector -O---K 100 100 000 - 0
198 Offline_Uncorrectable ---R-- 100 100 000 - 0
199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 5
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
GP Log at address 0x03 has 1 sectors [Ext. Comprehensive SMART error log]
GP Log at address 0x04 has 7 sectors [Device Statistics log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 1 sectors [Extended self-test log]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error log]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP Log at address 0x20 has 1 sectors [Streaming performance log]
GP Log at address 0x21 has 1 sectors [Write stream error log]
GP Log at address 0x22 has 1 sectors [Read stream error log]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 0 (1 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 32 Celsius
Power Cycle Min/Max Temperature: 25/32 Celsius
Lifetime Min/Max Temperature: 19/51 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -40/70 Celsius
Temperature History Size (Index): 128 (123)
Index Estimated Time Temperature Celsius
124 2014-03-13 02:40 38 *******************
... ..( 50 skipped). .. *******************
47 2014-03-13 03:31 38 *******************
48 2014-03-13 03:32 ? -
49 2014-03-13 03:33 38 *******************
... ..( 38 skipped). .. *******************
88 2014-03-13 04:12 38 *******************
89 2014-03-13 04:13 39 ********************
90 2014-03-13 04:14 38 *******************
91 2014-03-13 04:15 39 ********************
... ..( 6 skipped). .. ********************
98 2014-03-13 04:22 39 ********************
99 2014-03-13 04:23 ? -
100 2014-03-13 04:24 ? -
101 2014-03-13 04:25 39 ********************
... ..( 7 skipped). .. ********************
109 2014-03-13 04:33 39 ********************
110 2014-03-13 04:34 ? -
111 2014-03-13 04:35 ? -
112 2014-03-13 04:36 ? -
113 2014-03-13 04:37 25 ******
114 2014-03-13 04:38 26 *******
115 2014-03-13 04:39 27 ********
116 2014-03-13 04:40 27 ********
117 2014-03-13 04:41 28 *********
118 2014-03-13 04:42 29 **********
119 2014-03-13 04:43 29 **********
120 2014-03-13 04:44 30 ***********
121 2014-03-13 04:45 30 ***********
122 2014-03-13 04:46 31 ************
123 2014-03-13 04:47 31 ************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP Log 0x04)
Page Offset Size Value Description
1 ===== = = == General Statistics (rev 1) ==
1 0x008 4 438 Lifetime Power-On Resets
1 0x010 4 11134 Power-on Hours
1 0x018 6 12463579584 Logical Sectors Written
1 0x020 6 221286762 Number of Write Commands
1 0x028 6 278337383949 Logical Sectors Read
1 0x030 6 222192809 Number of Read Commands
3 ===== = = == Rotating Media Statistics (rev 1) ==
3 0x008 4 11131 Spindle Motor Power-on Hours
3 0x010 4 11131 Head Flying Hours
3 0x018 4 554 Head Load Events
3 0x020 4 0 Number of Reallocated Logical Sectors
3 0x028 4 7 Read Recovery Attempts
3 0x030 4 2 Number of Mechanical Start Failures
4 ===== = = == General Errors Statistics (rev 1) ==
4 0x008 4 0 Number of Reported Uncorrectable Errors
4 0x010 4 296 Resets Between Cmd Acceptance and Completion
5 ===== = = == Temperature Statistics (rev 1) ==
5 0x008 1 32 Current Temperature
5 0x010 1 37~ Average Short Term Temperature
5 0x018 1 38~ Average Long Term Temperature
5 0x020 1 51 Highest Temperature
5 0x028 1 19 Lowest Temperature
5 0x030 1 43~ Highest Average Short Term Temperature
5 0x038 1 0~ Lowest Average Short Term Temperature
5 0x040 1 41~ Highest Average Long Term Temperature
5 0x048 1 0~ Lowest Average Long Term Temperature
5 0x050 4 0 Time in Over-Temperature
5 0x058 1 60 Specified Maximum Operating Temperature
5 0x060 4 0 Time in Under-Temperature
5 0x068 1 0 Specified Minimum Operating Temperature
6 ===== = = == Transport Statistics (rev 1) ==
6 0x008 4 2266 Number of Hardware Resets
6 0x010 4 1818 Number of ASR Events
6 0x018 4 5 Number of Interface CRC Errors
|_ ~ normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 4 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
Are there specific smartctl options you would recommend that I use to test the drive?
-----Original Message-----
From: Simon Brand [mailto:simon.brand at postadigitale.de]
Sent: Wednesday, March 12, 2014 4:45 PM
To: General Discussion about Arch Linux
Subject: Re: [arch-general] talkingarch problems formatting partitions
Am 12.03.2014 19:38, schrieb Don Raikes:
> Hi Ary,
>
> I tried using:
>
> # mkfs -t ext2 /dev/sda1
>
> And got the same results.
> After a reboot, I tried:
> # mkfs -t ext3 /dev/sda3
>
> And got a lot of messages about how there is a problem with the disk, so I am now suspecting that my hdd has gone bad, so I will need to wait on installing arch until I have a new drive.
>
> -----Original Message-----
> From: Ary Kleinerman [mailto:akleinerman at buinet.com.ar]
> Sent: Wednesday, March 12, 2014 11:27 AM
> To: General Discussion about Arch Linux
> Subject: Re: [arch-general] talkingarch problems formatting partitions
>
> Have you tried with other filesystem type, to see what happens? Maybe it could be a bug
>
> On Wed, Mar 12, 2014 at 3:07 PM, Don Raikes <DON.RAIKES at oracle.com> wrote:
>> Hi,
>>
>> I downloaded the talkingarch-20140203-dual.iso yesterday and want to install it onto my desktop system.
>>
>>
>>
>> I booted into the talkingarchlinux system no problems, and used parted to create the partitions on my hard disk.
>>
>>
>>
>> When I go to format the partitions, as soon as I enter the command:
>>
>>
>>
>> # mkfs -t ext4 /dev/sda1
>>
>>
>>
>> The entire system locks up. I have to do a hard reboot of the system to get anything working again.
>>
>>
>>
>> Any idea why this might be happening?
>
>
>
> --
> Ing. Ary Kleinerman
> Building Networks S.A.
> Córdoba, Argentina
> +54 351 5544150
>
You can use smartctl to verify a hd problem.
More information about the arch-general
mailing list