[arch-general] smartctl - 199 UDMA_CRC_Error_Count

Apfelkuchen apfelkuchen at posteo.de
Fri Jul 24 10:51:47 UTC 2015


Hey,

I tested my hard drives with smartctl -a. And for 199
UDMA_CRC_Error_Count I get a raw value of 808. Should I worry about this
disk?

I'll post you below the whole output of smartctl -a. Someone said it
could be a CRC-Failure. But I don't know exactly what this means. This
is my backup drive. So it would be critical if it is something wrong
with this disk.

 smartctl -a /dev/sdd1
smartctl 6.4 2015-06-04 r4109 [x86_64-linux-4.1.2-2-ARCH] (local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate SV35
Device Model:     ST2000VX000-1ES164
Serial Number:    Z4Z1JHXZ
LU WWN Device Id: 5 000c50 079dbcc19
Firmware Version: CV26
User Capacity:    2.000.398.934.016 bytes [2,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Fri Jul 24 12:39:16 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine
completed
					without error or no self-test has ever
					been run.
Total time to complete Offline
data collection: 		(   80) seconds.
Offline data collection
capabilities: 			 (0x73) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 217) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x10b9)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE
UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   119   099   006    Pre-fail  Always
      -       212390608
  3 Spin_Up_Time            0x0003   096   096   000    Pre-fail  Always
      -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always
      -       470
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always
      -       0
  7 Seek_Error_Rate         0x000f   100   253   030    Pre-fail  Always
      -       654069
  9 Power_On_Hours          0x0032   099   099   000    Old_age   Always
      -       941
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always
      -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always
      -       384
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always
      -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always
      -       0
188 Command_Timeout         0x0032   100   098   000    Old_age   Always
      -       48
189 High_Fly_Writes         0x003a   092   092   000    Old_age   Always
      -       8
190 Airflow_Temperature_Cel 0x0022   070   055   045    Old_age   Always
      -       30 (Min/Max 27/30)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always
      -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always
      -       26
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always
      -       474
194 Temperature_Celsius     0x0022   030   045   000    Old_age   Always
      -       30 (0 13 0 0 0)
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always
      -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age
Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   182   000    Old_age   Always
      -       808

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


More information about the arch-general mailing list